Table of Contents
- 1 Is there a reset button on the Whirlpool Cabrio washer?
- 2 Why would a washing machine suddenly have no power?
- 3 Why did my washer just stopped working?
- 4 Is there a fuse in washing machines?
- 5 How do I clear the error code on my Whirlpool washer?
- 6 How do you clear the codes on a Whirlpool Cabrio?
- 7 When does the Whirlpool Cabrio washer go into standby mode?
- 8 What does f then 72 mean on Whirlpool Cabrio washer?
Go to your display pad and touch any button you see there. This sends a signal to your Cabrio to clear the error code. You can also press “PAUSE/CANCEL” if you feel more comfortable doing that. Choose a cycle and press “START.” This might sound crazy, but yes, it’s part of the reset function.
Why would a washing machine suddenly have no power?
Sometimes the cord can get moved and dislodged from the wall a bit. Obviously, if the power cord is not completely plugged in, there will be no power or lights. You can also see if there is an issue with the actual wall outlet by plugging the machine in somewhere else.
Why does my Whirlpool washer have no power?
Check to see if a household circuit breaker or Ground Fault Circuit Interrupter (GFCI) outlet has tripped. If so, reset the circuit breaker or Ground Fault Circuit Interrupter. If the washer is on a fuse box, check to see if a fuse has blown and replace it, if necessary.
How do you reset the sensor on a Whirlpool washing machine?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Why did my washer just stopped working?
There are a number of possible causes for your washing machine not working as it should. Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining.
Is there a fuse in washing machines?
Washing machines have fuses that protect them from power surges. The other fuse sits in the lid switch on some machines; if the washer overheats or there is a power surge, the washer will not run again until the fuse in the switch is replaced.
What do you do when your Whirlpool washer won’t start?
Washer needs a reset: Resetting the machine can cycle its power, enabling it to start again. Unplug the washing machine or turn off its power at the circuit breaker. After one minute, restore power and try starting the washer.
Where is the fuse on my Whirlpool washing machine?
The lid switch is on the top of the washer lid opening. Plug the washing machine in. The lid switch needs to be removed from the machine before the two screws that hold it in place can be removed. The fuse should be located.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you clear the codes on a Whirlpool Cabrio?
If that did not work, try the next Cabrio reset procedure:
- Touch any button on the display pad to clear the error code or press “Pause Cancel.”
- Choose another cycle and press “Start”.
- Disconnect the Cabrio from power if the error or problem comes back.
- Wait 5 minutes before restoring power.
What does the Whirlpool Cabrio washer light up like?
The LCD panel on Whirlpool Cabrio washers displays the stages of a cleaning cycle. The panel also lights up like a Christmas tree when there is a problem. Sometimes it is a series of letters and numbers; sometimes there are flashing lights accompanied by cryptic beeping sounds.
What does diagnostics test mode on Whirlpool Cabrio washer mean?
Diagnostics Test mode if a stuck key is detected. Standby mode if there is a user interface mismatch. F then 40 flashes when the ATC Thermistor is detected to be open or shorted. F then 41 flashes when the motor rotor position sensor (RPS) thermistor is detected to be open or shorted out.
When does the Whirlpool Cabrio washer go into standby mode?
Standby mode if there is a user interface mismatch. F then 40 flashes when the ATC Thermistor is detected to be open or shorted. F then 41 flashes when the motor rotor position sensor (RPS) thermistor is detected to be open or shorted out. F then 42 flashes when the heater thermistor is open or shorted.
What does f then 72 mean on Whirlpool Cabrio washer?
F then 54 flashes when the machine/motor control detects high current for the motor module. F then 72 flashes when the basket check routine fails to determine if the basket is re-engaged after being disengaged. Is the basket floating?